Page 1 of 2 12>
Topic Options
#38534 - 12/29/03 07:42 PM Putting a CD Player in the Lower DIN w/Pics and part Numbers
Dr. BrokenLimits Moderator Offline
Post Master Supreme


Registered: 03/12/02
Posts: 33787
Loc: Austin, TX
I have yet to see an actual post showing how this is done so I decided to take away all of the fear and take some pictures so I can show everyone just how easy it is. I had all of the dash parts stolen so as I was putting them back in I took some pictures.

But you need 4 parts. The first part you need is the actual cup holders from the 96-98 Civic. You will also need the plastic square that will become the radio surround. The last 2 parts are optional but make mounting the radio MUCH easier. They are the right and left radio brackets. They were an option in 96-98 and are pretty cheap and make this much easier so go ahead and pick them up...






The first thing I did was put the CD player in the 96-98 assembly. If you have the radio brakcets this is just as easy as mounting it in the top location. The CD player just bolts right in. It will look like this when the CD player is in the 96-98 Cup Holder Assembly.





Now you must remove the arm rest section of the center console. In order to do this there are 2 screws that are close the back seat and 2 screws that are closer up. Remove them and then remove the Arm Rest console.

Then you must remove the shift boot console. In order to do this you must unscrew the shift knob and remove the screws that hold the console.

Now you must remove the 99-00 Cup Holder assembly which can be done by removing a series of 6 screws. 4 of the screws are to the right and left of the cubby hole and the other 2 are located near the floor. You may now keep the 99-00 Cup Holder Assembly in case you decide to return the car to stock or sell it or throw it away.

You must also remove 12 volt power plug console. This has 2 screws which are located near the top. I am assuming you have already removed your CD player from its origional location and therefore it is assumed you have a hole in your dash where the CD player used to be...

The wiring harness that is currently located in your car that plugged into your CD player is long enough that you can go ahead and pull it down to the new radio mounting location. Gently pull it down to where the 12 Volt Power Plug Console would have been.

Now plug the CD player into the cars radio wiring harness and bolt the 96-98 Cup Holder in where the 99-00 Cup Holder used to be located. Replace all of the consoles by following the opposite directions from above. The finished product should look like this:





Note that my car contains the 99-00 Civic DX radio block of plate Part #220475 PANEL, RADIO *NH1L*


I will be editing this how to to make it easier to read as well as posting pictures of the console removal process. I was just bored sitting here in Orlando and deicided to get this started...

If you have any questions feel free to AIM or E-mail me the addresses are located in my Signature...
_________________________
/Brandon

Top
Visit Sponsors! Help CSi !
#38535 - 12/29/03 08:37 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Neo Noodle Offline
Sr Member


Registered: 06/17/02
Posts: 1115
Loc: Honolulu, HI
Awsome I've been thinking about doing this for a long time now.. Does it have to be the 96-98 cup holders? I like my 99-00 ones better
_________________________
Breakfast: McDonalds Spam Delux Platter ALL Rice
Lunch: Teri Chicken & Rice
Dinner: Beef Stew & Rice
"You are what you eat."


Top
#38536 - 12/29/03 09:19 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
SiRacer Offline
Post Master Supreme


Registered: 10/25/99
Posts: 22862
Loc: Phoenix, AZ
Quote:

Awsome I've been thinking about doing this for a long time now.. Does it have to be the 96-98 cup holders? I like my 99-00 ones better




Yes

Top
#38537 - 12/29/03 10:58 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Air_Siren_Si Offline
Jr Member


Registered: 03/23/03
Posts: 468
Loc: Denver, CO
Quote:

Awsome I've been thinking about doing this for a long time now.. Does it have to be the 96-98 cup holders? I like my 99-00 ones better




Yeah with how well they hold cups and all, how can you not?
_________________________

Top
#38538 - 12/29/03 11:07 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Dr. BrokenLimits Moderator Offline
Post Master Supreme


Registered: 03/12/02
Posts: 33787
Loc: Austin, TX
haha the 96-98 hold cups MUCH better in my opinion...
_________________________
/Brandon

Top
#38539 - 12/30/03 12:35 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Sichology101 Offline
Member


Registered: 04/29/03
Posts: 801
Loc: SouthEast
thanks for a great post...going in my favorites....U da Man!
_________________________
www.joecartoon.com Pisces (Feb 23 - Mar 22) You are a pioneer type and think most people
are dickheads. You are quick to reprimand, impatient and full of advice. You
do nothing but piss-off everyone you come in contact with. You are a
prick.

Top
#38540 - 12/30/03 10:20 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
VTEC976 Offline
Post Master Sr


Registered: 08/09/02
Posts: 5263
Loc: Doing AWD Doughnuts in Denver
Nice tutorial.
_________________________
-Gabe
MK4 DBP R32
One Bicycle

Top
#38541 - 12/30/03 10:34 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
gok Offline
Post Master Supreme


Registered: 01/04/00
Posts: 11821
Loc: Panama City, FL
actually, no I did mine with my 99-00 cupholders and it worked fine. you have to do some trimming but it fits and looks good.
Top
#38542 - 12/30/03 02:37 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
CivicSiEBP Offline
Poster


Registered: 11/21/99
Posts: 324
Loc: NJ
What are some of the benefits of doing this. Does it make it harder to steal the radio? Also why not leave the stock radio in at the top so that if a thief is doing a "walkby" he will only see a stock radio and keep walking.
_________________________
Aim- CivicVTEC160 1999 Civic Si 2004 Nissan Pathfinder

Top
#38543 - 12/30/03 06:29 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Dr. BrokenLimits Moderator Offline
Post Master Supreme


Registered: 03/12/02
Posts: 33787
Loc: Austin, TX
If you flip open the cup holder the radio is not visible...
_________________________
/Brandon

Top
#38544 - 12/31/03 08:49 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
jjtackleberry Offline
Jr Member


Registered: 03/21/02
Posts: 446
Loc: KS
Quote:

What are some of the benefits of doing this. Does it make it harder to steal the radio? Also why not leave the stock radio in at the top so that if a thief is doing a "walkby" he will only see a stock radio and keep walking.


_________________________
only if you get caught........

Top
#38545 - 12/31/03 11:10 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Dr. BrokenLimits Moderator Offline
Post Master Supreme


Registered: 03/12/02
Posts: 33787
Loc: Austin, TX
friend of mine has his stock CD player up top and below he has his nice CD player...
_________________________
/Brandon

Top
#38546 - 12/31/03 02:00 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
bbyboo1323 Offline
Poster


Registered: 05/13/02
Posts: 249
Loc: VA
why would you need 2 cd players tho? just put a screen or a custom plate for some gauges ors omething up top
Top
#38547 - 01/01/04 08:38 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
kyden Offline
Post Master Supreme


Registered: 12/20/99
Posts: 15406
Loc: Providence, RI
theft deterrent.. if they see the stock radio, they won't assume there's an aftermarket one in there..
_________________________
<x> i had a weird dream <x> where i lived in an apartment complex <x> walked down the street, and kyden and a couple other dudes were living in an apartment and ran outside looking for the maintenance people <x> and something about taking a shit in a sealed toilet

Top
#38548 - 01/01/04 03:04 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Chris732 Offline
Newbie


Registered: 01/01/04
Posts: 1
Where is a good place on line to get these parts...ie cheapest ect
Top
#38549 - 01/01/04 05:20 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
hemz86 Offline
Jr Poster


Registered: 09/16/03
Posts: 90
I just did the swap today in my 98 civic and it turned out great, i decided that maybe instead of putting in a blank plate i was going to try using fiberglass with a reverse civic sticker and having red behind it for a little added interior flare. Maybe maybe not depends on how gutsy i am.
_________________________
Drive it like you stole it

Top
#38550 - 01/01/04 05:28 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Dr. BrokenLimits Moderator Offline
Post Master Supreme


Registered: 03/12/02
Posts: 33787
Loc: Austin, TX
What? You did the swap in a 98 Civic? The 98 Civic already has that cup holder assembly...
_________________________
/Brandon

Top
#38551 - 01/01/04 05:48 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
hemz86 Offline
Jr Poster


Registered: 09/16/03
Posts: 90
Meaning i took it from the upper slot and moved it into the lower slot.
_________________________
Drive it like you stole it

Top
#38552 - 01/01/04 07:42 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
toddt_02 Offline
Member


Registered: 02/09/03
Posts: 774
Loc: VA
I like the idea but can't think of anything to put up top in its place........stock cd player........just a waste to me and solid looks crap.........ideally a tv but then the $ vs college issue.................anything other than a tv to go there? I think its the only thing that would really look "right."
Top
#38553 - 01/01/04 09:36 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Shift125x Offline
Jr Poster


Registered: 11/21/03
Posts: 144
Loc: NC
Sweet how To man! Im thinking about doing the same thing. and to answer your question about what might look good in the stock location. This is probably what ill do, get a block off plate and mount my V-AFC in it. How do ya'll think that would look/work?
_________________________
IM = BradXNCSU

Top
#38554 - 01/01/04 09:39 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
CivicSiEBP Offline
Poster


Registered: 11/21/99
Posts: 324
Loc: NJ
Too bad you can't fit a CD changer in there
_________________________
Aim- CivicVTEC160 1999 Civic Si 2004 Nissan Pathfinder

Top
#38555 - 01/02/04 11:55 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Neo Noodle Offline
Sr Member


Registered: 06/17/02
Posts: 1115
Loc: Honolulu, HI
Quote:

Yeah with how well they hold cups and all, how can you not?



Quote:

haha the 96-98 hold cups MUCH better in my opinion...




Acctually It's because I need all that extra room that makes cups bounce around or fall out of the holder to be able to put a cup in there. That is because I have the OEM cigarette lighter/ash tray attachment.. I can barely get any cup in there now.. It's not uncommon for me to have to remove the insert just to have enuff room to angle the cup in there. I don't have to worry about it falling out tho sinse they can't tilt too much because the top is right next to my smokin package
_________________________
Breakfast: McDonalds Spam Delux Platter ALL Rice
Lunch: Teri Chicken & Rice
Dinner: Beef Stew & Rice
"You are what you eat."


Top
#38556 - 01/03/04 09:38 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
VtecBio009 Offline
Post Master Sr


Registered: 09/07/02
Posts: 4940
Loc: California
very creative. good trick
_________________________
· pR0n ·
I SIMPLY LIVE, NOT LIVE FOR
2004 Triumph Daytona 600
2003 Infiniti G35
2002 Acura CL Type-S

2000 Honda Civic SI
1998 Honda Civic EX
1994 Honda Accord LX

Top
#38557 - 01/03/04 03:55 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Dr. BrokenLimits Moderator Offline
Post Master Supreme


Registered: 03/12/02
Posts: 33787
Loc: Austin, TX
Well mine is running a 7 inch LCD for my Hondata and a navigation system off the laptop that is currently located under the seat...
_________________________
/Brandon

Top
#38558 - 01/05/04 05:29 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
TranZenD si 209 Offline
Major Member


Registered: 04/03/00
Posts: 1473
Loc: Stockton, CA
im about to do that soon also, as soon passwordjdm.com ever sends me my damn cf block off plate. i been waiting for a month now. they dont even give me a email confirmation or any kind of email at all and not even call me for the shipping delay cause they had to order me a new one from japan. freaking liars, they told me they had one left in stock when i made the call to order it. the cf block off plate is the onlything i have left to get before i put my system in. i got my deck, the cupholder, the optional ashtray and cig lighter, my jl interior speakers, and my amp and wiring.
_________________________
2000 MR SI, Ready! Set! Go! AIM - swtguy2luvu Email - anekin007@yahoo.com

Top
#38559 - 01/05/04 07:06 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
*darkjedi022 Offline
Member


Registered: 09/27/01
Posts: 807
Loc: Maryland
hey im trying to put my vafc behind the 96-98 cup holders...what would i need?? i know need the cup holder part number 21707...21712v and 21713 brackets...what else???????
_________________________
my attitude is fuck it ....muthafuckas luv it

Top
#38560 - 01/08/04 02:48 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
mangus Offline
Newbie


Registered: 01/07/04
Posts: 63
Loc: Cincinnati, OH
the only bad thing is that the "lid" on the 96-98 cupholder gets sticky and doesnt like to open/close sometimes, or think about having a drink in the cupholder, and having to remove it every time you need to change the station on your radio.
Top
#38561 - 01/08/04 10:55 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Dr. BrokenLimits Moderator Offline
Post Master Supreme


Registered: 03/12/02
Posts: 33787
Loc: Austin, TX
if you have a remote, it works around the cup holder in my case...

So if I have drinks in it I can still change the stations and tracks but if i need to change CDs I have to remove the drinks...

But you all own Si's you shouldnt be allowing people to drink anything in your car
_________________________
/Brandon

Top
#38562 - 01/09/04 05:53 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
HOOPT Offline
Post Master


Registered: 07/20/02
Posts: 2009
Loc: meh
Quote:

theft deterrent.. if they see the stock radio, they won't assume there's an aftermarket one in there..




thats is correct keep the stock for a theft deterrent

heres how mine looks






Edited by HOOPT (01/10/04 06:28 PM)
_________________________
US Paratrooper....the ORIGINAL Precision Guided SMART Weapon!!
07 Volvo S60R
06 STi SGM (R.I.P Totaled)
00 Si FBP (R.I.P)

Top
#38563 - 01/27/04 12:42 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
SiWheelman Offline
Post Master


Registered: 03/09/02
Posts: 2512
Quote:

hey im trying to put my vafc behind the 96-98 cup holders...what would i need?? i know need the cup holder part number 21707...21712v and 21713 brackets...what else???????




get all of the parts listed to do the radio install and the vafc fits in there perfectly. You can then fabricate a piece of cf to go around the rest of the area if you want, or you can leave it alone and be able to take out the vafc whenever you want to or lower it down under to hide it.

Top
#38564 - 02/13/04 08:34 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
*darkjedi022 Offline
Member


Registered: 09/27/01
Posts: 807
Loc: Maryland
well i want to keep the stock pocket...and just put the cup holders to cover it up ..is that possible.............or do i haev to get the brackets too??.....
_________________________
my attitude is fuck it ....muthafuckas luv it

Top
#38565 - 02/24/04 08:44 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Num
Dr. BrokenLimits Moderator Offline
Post Master Supreme


Registered: 03/12/02
Posts: 33787
Loc: Austin, TX
yeah just dont put in the brackets
_________________________
/Brandon

Top
#38566 - 02/25/04 09:55 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Num
*darkjedi022 Offline
Member


Registered: 09/27/01
Posts: 807
Loc: Maryland
hey thanks..i willl post some pics...so i can show yall how it looks.....
_________________________
my attitude is fuck it ....muthafuckas luv it

Top
#38567 - 02/25/04 04:18 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Num
offdahook_civic Offline
Jr Poster


Registered: 12/10/03
Posts: 94
wouldn't the cup holder cover block the way of the stereo??? if u have drinks in ur cup holder than you can put in a cd or anything like that.
_________________________
[image]http://static.howstuffworks.com/gif/engine-cam.gif[/image]

Top
#38568 - 02/25/04 08:12 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Num
skeezerhunter Offline
Major Member


Registered: 01/26/04
Posts: 1449
Quote:

wouldn't the cup holder cover block the way of the stereo??? if u have drinks in ur cup holder than you can put in a cd or anything like that.




You obviously canNOT read.

Try reading before posting dumb questions, that's already been answered a few posts prior to yours.
_________________________

Top
Page 1 of 2 12>


Moderator:  Dr. BrokenLimits, Professor Paki 
Hop to:
Shout Box

CSi Sponsors


ClubSi.com Shirts
ClubSi-Shirts
GameStop
Black-Friday Specials
Big Brake Kits
StopTech.Sale BBK Clearance
Brake Kits
Buy Brake Kits
EBC Brake Kits
EBC Brake Kits
BuyBrakes
Brake Kits-Pads & Rotors Sets
StopTech Brake Kits
StopTech
StopTech NZ
StopTech
StopTech Australia
StopTech
Hawk Brake Pads
Hawk Brake Pads
Samys Camera
GoPros, Cameras, Gear
Brake Specials Near Me
Brake Specials Near Me
Brake Pad Coupons
Coupon Code "hondafetish"
Porsche Brakes
Porsche Brake Upgrades
2-Piece Rotors-Civic Type-R
2-Piece Civic Rotors
Advertisement

| Brake Pads | | How To Change Brake Pads | | Drilled Slotted Brake Kits Cheap | EBC Brake Kits | Performance Brake Kits | Brake Specials Near Me | How To Replace Brake Pads