Putting a CD Player in the Lower DIN w/Pics and part Numbers

You are not logged in. [Log In] ClubSi » Forums » General Zone » Tips & Tricks » Putting a CD Player in the Lower DIN w/Pics and part Numbers

Page 1 of 2

Topic Options

#38534 - 12/29/03 07:42 PM Putting a CD Player in the Lower DIN w/Pics and part Numbers
Dr. BrokenLimits Dr. BrokenLimits Post Master Supreme Registered: 03/12/02 Posts: 33862 Loc: Austin, TX	I have yet to see an actual post showing how this is done so I decided to take away all of the fear and take some pictures so I can show everyone just how easy it is. I had all of the dash parts stolen so as I was putting them back in I took some pictures. But you need 4 parts. The first part you need is the actual cup holders from the 96-98 Civic. You will also need the plastic square that will become the radio surround. The last 2 parts are optional but make mounting the radio MUCH easier. They are the right and left radio brackets. They were an option in 96-98 and are pretty cheap and make this much easier so go ahead and pick them up... The first thing I did was put the CD player in the 96-98 assembly. If you have the radio brakcets this is just as easy as mounting it in the top location. The CD player just bolts right in. It will look like this when the CD player is in the 96-98 Cup Holder Assembly. Now you must remove the arm rest section of the center console. In order to do this there are 2 screws that are close the back seat and 2 screws that are closer up. Remove them and then remove the Arm Rest console. Then you must remove the shift boot console. In order to do this you must unscrew the shift knob and remove the screws that hold the console. Now you must remove the 99-00 Cup Holder assembly which can be done by removing a series of 6 screws. 4 of the screws are to the right and left of the cubby hole and the other 2 are located near the floor. You may now keep the 99-00 Cup Holder Assembly in case you decide to return the car to stock or sell it or throw it away. You must also remove 12 volt power plug console. This has 2 screws which are located near the top. I am assuming you have already removed your CD player from its origional location and therefore it is assumed you have a hole in your dash where the CD player used to be... The wiring harness that is currently located in your car that plugged into your CD player is long enough that you can go ahead and pull it down to the new radio mounting location. Gently pull it down to where the 12 Volt Power Plug Console would have been. Now plug the CD player into the cars radio wiring harness and bolt the 96-98 Cup Holder in where the 99-00 Cup Holder used to be located. Replace all of the consoles by following the opposite directions from above. The finished product should look like this: Note that my car contains the 99-00 Civic DX radio block of plate Part #220475 PANEL, RADIO NH1L I will be editing this how to to make it easier to read as well as posting pictures of the console removal process. I was just bored sitting here in Orlando and deicided to get this started... If you have any questions feel free to AIM or E-mail me the addresses are located in my Signature... _________________________ /Brandon
Top

Visit Sponsors! Help CSi !

#38535 - 12/29/03 08:37 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Neo Noodle Neo Noodle Sr Member Registered: 06/17/02 Posts: 1115 Loc: Honolulu, HI	Awsome I've been thinking about doing this for a long time now.. Does it have to be the 96-98 cup holders? I like my 99-00 ones better _________________________ Breakfast: McDonalds Spam Delux Platter ALL Rice Lunch: Teri Chicken & Rice Dinner: Beef Stew & Rice "You are what you eat."
Top

#38536 - 12/29/03 09:19 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
SiRacer SiRacer Post Master Supreme Registered: 10/25/99 Posts: 22862 Loc: Phoenix, AZ	Quote: Awsome I've been thinking about doing this for a long time now.. Does it have to be the 96-98 cup holders? I like my 99-00 ones better Yes
Top

#38537 - 12/29/03 10:58 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Air_Siren_Si Air_Siren_Si Jr Member Registered: 03/23/03 Posts: 468 Loc: Denver, CO	Quote: Awsome I've been thinking about doing this for a long time now.. Does it have to be the 96-98 cup holders? I like my 99-00 ones better Yeah with how well they hold cups and all, how can you not? _________________________
Top

#38538 - 12/29/03 11:07 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Dr. BrokenLimits Dr. BrokenLimits Post Master Supreme Registered: 03/12/02 Posts: 33862 Loc: Austin, TX	haha the 96-98 hold cups MUCH better in my opinion... _________________________ /Brandon
Top

#38539 - 12/30/03 12:35 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Sichology101 Sichology101 Member Registered: 04/29/03 Posts: 801 Loc: SouthEast	thanks for a great post...going in my favorites....U da Man! _________________________ www.joecartoon.com Pisces (Feb 23 - Mar 22) You are a pioneer type and think most people are dickheads. You are quick to reprimand, impatient and full of advice. You do nothing but piss-off everyone you come in contact with. You are a prick.
Top

#38540 - 12/30/03 10:20 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
VTEC976 VTEC976 Post Master Sr Registered: 08/09/02 Posts: 5263 Loc: Doing AWD Doughnuts in Denver	Nice tutorial. _________________________ -Gabe MK4 DBP R32 One Bicycle
Top

#38541 - 12/30/03 10:34 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
gok gok Post Master Supreme Registered: 01/04/00 Posts: 11821 Loc: Panama City, FL	actually, no I did mine with my 99-00 cupholders and it worked fine. you have to do some trimming but it fits and looks good.
Top

#38542 - 12/30/03 02:37 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
CivicSiEBP CivicSiEBP Poster Registered: 11/21/99 Posts: 324 Loc: NJ	What are some of the benefits of doing this. Does it make it harder to steal the radio? Also why not leave the stock radio in at the top so that if a thief is doing a "walkby" he will only see a stock radio and keep walking. _________________________ Aim- CivicVTEC160 1999 Civic Si 2004 Nissan Pathfinder
Top

#38543 - 12/30/03 06:29 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Dr. BrokenLimits Dr. BrokenLimits Post Master Supreme Registered: 03/12/02 Posts: 33862 Loc: Austin, TX	If you flip open the cup holder the radio is not visible... _________________________ /Brandon
Top

#38544 - 12/31/03 08:49 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
jjtackleberry jjtackleberry Jr Member Registered: 03/21/02 Posts: 446 Loc: KS	Quote: What are some of the benefits of doing this. Does it make it harder to steal the radio? Also why not leave the stock radio in at the top so that if a thief is doing a "walkby" he will only see a stock radio and keep walking. _________________________ only if you get caught........
Top

#38545 - 12/31/03 11:10 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Dr. BrokenLimits Dr. BrokenLimits Post Master Supreme Registered: 03/12/02 Posts: 33862 Loc: Austin, TX	friend of mine has his stock CD player up top and below he has his nice CD player... _________________________ /Brandon
Top

#38546 - 12/31/03 02:00 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
bbyboo1323 bbyboo1323 Poster Registered: 05/13/02 Posts: 249 Loc: VA	why would you need 2 cd players tho? just put a screen or a custom plate for some gauges ors omething up top
Top

#38547 - 01/01/04 08:38 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
kyden kyden Post Master Supreme Registered: 12/20/99 Posts: 15406 Loc: Providence, RI	theft deterrent.. if they see the stock radio, they won't assume there's an aftermarket one in there.. _________________________ <x> i had a weird dream <x> where i lived in an apartment complex <x> walked down the street, and kyden and a couple other dudes were living in an apartment and ran outside looking for the maintenance people <x> and something about taking a shit in a sealed toilet
Top

#38548 - 01/01/04 03:04 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Chris732 Chris732 Newbie Registered: 01/01/04 Posts: 1	Where is a good place on line to get these parts...ie cheapest ect
Top

#38549 - 01/01/04 05:20 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
hemz86 hemz86 Jr Poster Registered: 09/16/03 Posts: 90	I just did the swap today in my 98 civic and it turned out great, i decided that maybe instead of putting in a blank plate i was going to try using fiberglass with a reverse civic sticker and having red behind it for a little added interior flare. Maybe maybe not depends on how gutsy i am. _________________________ Drive it like you stole it
Top

#38550 - 01/01/04 05:28 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Dr. BrokenLimits Dr. BrokenLimits Post Master Supreme Registered: 03/12/02 Posts: 33862 Loc: Austin, TX	What? You did the swap in a 98 Civic? The 98 Civic already has that cup holder assembly... _________________________ /Brandon
Top

#38551 - 01/01/04 05:48 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
hemz86 hemz86 Jr Poster Registered: 09/16/03 Posts: 90	Meaning i took it from the upper slot and moved it into the lower slot. _________________________ Drive it like you stole it
Top

#38552 - 01/01/04 07:42 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
toddt_02 toddt_02 Member Registered: 02/09/03 Posts: 774 Loc: VA	I like the idea but can't think of anything to put up top in its place........stock cd player........just a waste to me and solid looks crap.........ideally a tv but then the $ vs college issue.................anything other than a tv to go there? I think its the only thing that would really look "right."
Top

#38553 - 01/01/04 09:36 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Shift125x Shift125x Jr Poster Registered: 11/21/03 Posts: 144 Loc: NC	Sweet how To man! Im thinking about doing the same thing. and to answer your question about what might look good in the stock location. This is probably what ill do, get a block off plate and mount my V-AFC in it. How do ya'll think that would look/work? _________________________ IM = BradXNCSU
Top

#38554 - 01/01/04 09:39 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
CivicSiEBP CivicSiEBP Poster Registered: 11/21/99 Posts: 324 Loc: NJ	Too bad you can't fit a CD changer in there _________________________ Aim- CivicVTEC160 1999 Civic Si 2004 Nissan Pathfinder
Top

#38555 - 01/02/04 11:55 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Neo Noodle Neo Noodle Sr Member Registered: 06/17/02 Posts: 1115 Loc: Honolulu, HI	Quote: Yeah with how well they hold cups and all, how can you not? Quote: haha the 96-98 hold cups MUCH better in my opinion... Acctually It's because I need all that extra room that makes cups bounce around or fall out of the holder to be able to put a cup in there. That is because I have the OEM cigarette lighter/ash tray attachment.. I can barely get any cup in there now.. It's not uncommon for me to have to remove the insert just to have enuff room to angle the cup in there. I don't have to worry about it falling out tho sinse they can't tilt too much because the top is right next to my smokin package _________________________ Breakfast: McDonalds Spam Delux Platter ALL Rice Lunch: Teri Chicken & Rice Dinner: Beef Stew & Rice "You are what you eat."
Top

#38556 - 01/03/04 09:38 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
VtecBio009 VtecBio009 Post Master Sr Registered: 09/07/02 Posts: 4940 Loc: California	very creative. good trick _________________________ · pR0n · I SIMPLY LIVE, NOT LIVE FOR 2004 Triumph Daytona 600 2003 Infiniti G35 2002 Acura CL Type-S 2000 Honda Civic SI 1998 Honda Civic EX 1994 Honda Accord LX
Top

#38557 - 01/03/04 03:55 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Dr. BrokenLimits Dr. BrokenLimits Post Master Supreme Registered: 03/12/02 Posts: 33862 Loc: Austin, TX	Well mine is running a 7 inch LCD for my Hondata and a navigation system off the laptop that is currently located under the seat... _________________________ /Brandon
Top

#38558 - 01/05/04 05:29 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
TranZenD si 209 TranZenD si 209 Major Member Registered: 04/03/00 Posts: 1473 Loc: Stockton, CA	im about to do that soon also, as soon passwordjdm.com ever sends me my damn cf block off plate. i been waiting for a month now. they dont even give me a email confirmation or any kind of email at all and not even call me for the shipping delay cause they had to order me a new one from japan. freaking liars, they told me they had one left in stock when i made the call to order it. the cf block off plate is the onlything i have left to get before i put my system in. i got my deck, the cupholder, the optional ashtray and cig lighter, my jl interior speakers, and my amp and wiring. _________________________ 2000 MR SI, Ready! Set! Go! AIM - swtguy2luvu Email - anekin007@yahoo.com
Top

#38559 - 01/05/04 07:06 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
darkjedi022 darkjedi022 Member Registered: 09/27/01 Posts: 807 Loc: Maryland	hey im trying to put my vafc behind the 96-98 cup holders...what would i need?? i know need the cup holder part number 21707...21712v and 21713 brackets...what else??????? _________________________ my attitude is fuck it ....muthafuckas luv it
Top

#38560 - 01/08/04 02:48 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
mangus mangus Newbie Registered: 01/07/04 Posts: 63 Loc: Cincinnati, OH	the only bad thing is that the "lid" on the 96-98 cupholder gets sticky and doesnt like to open/close sometimes, or think about having a drink in the cupholder, and having to remove it every time you need to change the station on your radio.
Top

#38561 - 01/08/04 10:55 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
Dr. BrokenLimits Dr. BrokenLimits Post Master Supreme Registered: 03/12/02 Posts: 33862 Loc: Austin, TX	if you have a remote, it works around the cup holder in my case... So if I have drinks in it I can still change the stations and tracks but if i need to change CDs I have to remove the drinks... But you all own Si's you shouldnt be allowing people to drink anything in your car _________________________ /Brandon
Top

#38562 - 01/09/04 05:53 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
HOOPT HOOPT Post Master Registered: 07/20/02 Posts: 2009 Loc: meh	Quote: theft deterrent.. if they see the stock radio, they won't assume there's an aftermarket one in there.. thats is correct keep the stock for a theft deterrent heres how mine looks Edited by HOOPT (01/10/04 06:28 PM) _________________________ US Paratrooper....the ORIGINAL Precision Guided SMART Weapon!! 07 Volvo S60R 06 STi SGM (R.I.P Totaled) 00 Si FBP (R.I.P)
Top

#38563 - 01/27/04 12:42 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
SiWheelman SiWheelman Post Master Registered: 03/09/02 Posts: 2512	Quote: hey im trying to put my vafc behind the 96-98 cup holders...what would i need?? i know need the cup holder part number 21707...21712v and 21713 brackets...what else??????? get all of the parts listed to do the radio install and the vafc fits in there perfectly. You can then fabricate a piece of cf to go around the rest of the area if you want, or you can leave it alone and be able to take out the vafc whenever you want to or lower it down under to hide it.
Top

#38564 - 02/13/04 08:34 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Numbers
darkjedi022 darkjedi022 Member Registered: 09/27/01 Posts: 807 Loc: Maryland	well i want to keep the stock pocket...and just put the cup holders to cover it up ..is that possible.............or do i haev to get the brackets too??..... _________________________ my attitude is fuck it ....muthafuckas luv it
Top

#38565 - 02/24/04 08:44 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Num
Dr. BrokenLimits Dr. BrokenLimits Post Master Supreme Registered: 03/12/02 Posts: 33862 Loc: Austin, TX	yeah just dont put in the brackets _________________________ /Brandon
Top

#38566 - 02/25/04 09:55 AM Re: Putting a CD Player in the Lower DIN w/Pics and part Num
darkjedi022 darkjedi022 Member Registered: 09/27/01 Posts: 807 Loc: Maryland	hey thanks..i willl post some pics...so i can show yall how it looks..... _________________________ my attitude is fuck it ....muthafuckas luv it
Top

#38567 - 02/25/04 04:18 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Num
offdahook_civic offdahook_civic Jr Poster Registered: 12/10/03 Posts: 94	wouldn't the cup holder cover block the way of the stereo??? if u have drinks in ur cup holder than you can put in a cd or anything like that. _________________________ [image]http://static.howstuffworks.com/gif/engine-cam.gif[/image]
Top

#38568 - 02/25/04 08:12 PM Re: Putting a CD Player in the Lower DIN w/Pics and part Num
skeezerhunter skeezerhunter Major Member Registered: 01/26/04 Posts: 1449	Quote: wouldn't the cup holder cover block the way of the stereo??? if u have drinks in ur cup holder than you can put in a cd or anything like that. You obviously canNOT read. Try reading before posting dumb questions, that's already been answered a few posts prior to yours. _________________________
Top

Page 1 of 2

Previous Topic View All Topics

Index Next Topic

Moderator: Dr. BrokenLimits, Professor Paki

Hop to:

Shout Box

CSi Sponsors

ClubSi.com Shirts
ClubSi-Shirts
GameStop
Black-Friday Specials
Big Brake Kits
StopTech.Sale BBK Clearance
Brake Kits
Buy Brake Kits
EBC Brake Kits
EBC Brake Kits
BuyBrakes
Brake Kits-Pads & Rotors Sets
StopTech Brake Kits
StopTech
StopTech NZ
StopTech
StopTech Australia
StopTech
Hawk Brake Pads
Hawk Brake Pads
Samys Camera
GoPros, Cameras, Gear
Brake Specials Near Me
Brake Specials Near Me
Brake Pad Coupons
Coupon Code "hondafetish"
Porsche Brakes
Porsche Brake Upgrades
2-Piece Rotors-Civic Type-R
2-Piece Civic Rotors