You are not logged in. [Log In] ClubSi » Forums » General Zone » Tips & Tricks » Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
Register User       Forum List       Calendar       FAQ      
Page 1 of 3 123>
Topic Options
#50723 - 07/09/04 06:21 PM Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
SiToeKnee Offline
Major Member


Registered: 11/13/03
Posts: 1447
Loc: Irvine, CA
Kenny (Trixiem) and myself decided to pick up a set of the JDM EK9 sidemarkers from ICB Motorsport in Temple City.
ICB Motorsport Homepage


We printed out a template and used guidelines from this site:
Template and Tips for Sidemarker cutting
The person on the site mentioned they cut the hole smaller than the template, but we found that the template was an exact fit leaving the notch alone and simply following the lines to cut the holes.

The template we followed:


Here is the placement on the fender, 155 mm from the top of the molding to the bottom of the tape and 140 mm from the edge of the door to the edge of the tape.


We then found the center of the intersection, which is where the exact center of the sidemarker:


We then found the center of the template and lined up the two over each other and taped it down.


A drill was used to make the initial hole, then we used a "Metal Nibbler" from RadioShack ($12.99):

(This thing was awesome, and it cut very precisely, even though it took awhile, probably better than using a dremel.)

Getting started on the fender (EEEEEP!). I look scared in that picture. Poor fender.


"T" is for Tony!!


The final hole:


After cutting the hole, add place some touch up paint on the bare metal to help prevent rust. We also plan to get a rubber ring to create a tight seal around the sidemarker or use plumber's putty to help it.

Kenny wiring up the sidemarkers:


There are two wiring options. USDM (Sidemarker only blinks when turn signal is on) or JDM (Sidemarkers stay on and blink alternately with the signal). Pull back the fender liner and remove the corner/parking light. There will be 3 wires going to the bulb. Tap into the corresponding wires for each blinking style.

USDM:
Tap into green(turn signal) and black(ground) wire.
JDM:
Tap into red(parking light) and green(turn signal) wire.

Sidemarker is in!


Installed sidemarkers on our cars:



Practice fender we had before we started:


Practice fender after a hard day of work:


That's about it folks. Hope this is helpful to you all. Thanks for looking.

Edited by SiToeKnee (07/09/04 10:46 PM)
_________________________
99 EBP Si I/H/E

Top
Visit Sponsors! Help CSi !
#50724 - 07/09/04 06:52 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
hondajunkie Offline
Post Master Sr


Registered: 09/19/03
Posts: 5620
Loc: Behind Donut Man
always wanted to do that. looks good. Good how-to also.
Top
#50725 - 07/09/04 08:27 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
Dr. BrokenLimits Moderator Offline
Post Master Supreme


Registered: 03/12/02
Posts: 33827
Loc: Austin, TX
Nice guys. If I ever get a damn website again I will add it to mine.
_________________________
/Brandon

Top
#50726 - 07/09/04 08:44 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
Trixiem Offline
Post Master Sr


Registered: 03/10/03
Posts: 3031
Loc: Las Vegas, Nv
haha we'd be honored broken, the install wasn't that hard. Also we screwed up a little bit where a corner is showing but you can only see it if you look at it at all angels. Was nerve wrecking cutting into fenders even tho tony did most of the cutting cause i'm a pussy haha. Forgot to mention to use touch up paint to prevent rust on the cut surfaces, i didn't have any VSM so i used tonys EBP touch up on my VSM lol

-kenny
Top
#50727 - 07/09/04 10:45 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
SiToeKnee Offline
Major Member


Registered: 11/13/03
Posts: 1447
Loc: Irvine, CA
Quote:

haha we'd be honored broken, the install wasn't that hard. Also we screwed up a little bit where a corner is showing but you can only see it if you look at it at all angels. Was nerve wrecking cutting into fenders even tho tony did most of the cutting cause i'm a pussy haha. Forgot to mention to use touch up paint to prevent rust on the cut surfaces, i didn't have any VSM so i used tonys EBP touch up on my VSM lol

-kenny



oops, knew i forgot to add something. i'll put that in now.
_________________________
99 EBP Si I/H/E

Top
#50728 - 07/09/04 11:33 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
sky1004db Offline
Jr Member


Registered: 02/09/04
Posts: 471
Loc: so-cal
this should be a sticky :D
_________________________
00` EBP SIR-T - stolen, stripped, and totaled 02' minivan AIM: sky1004eric

Top
#50729 - 07/10/04 10:20 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
marcos Offline
Poster


Registered: 08/13/02
Posts: 294
Loc: College Station, TX
Nice write up, definately has me thinking about doing it now.
_________________________
2000 FBP EM1

Top
#50730 - 07/10/04 11:45 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
Bonedust Offline
Jr Member


Registered: 03/01/03
Posts: 632
Loc: Riverside, CA
Good information, thanks
_________________________
2000 MR SI -- Stolen AIM: l3oNeDuST

Top
#50731 - 07/11/04 12:48 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
GTGOTEN Offline
Jr Member


Registered: 02/27/03
Posts: 628
Loc: MY AMI
Quote:

Good information, thanks



_________________________
For the Love of the Music....

Top
#50732 - 07/14/04 12:16 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
Sir Ironpool Offline
Sponsored by Toyota
Post Master Supreme


Registered: 03/12/01
Posts: 71803
Loc: Long Beach, CA
Good job guys. I'm impressed that you finally did it after all that talk. I told you it wasn't that difficult. The nibblers work pretty goo, huh?

Way to go on the write up. I never have the patiuence to document all my DIYs, so this should help everybody out.
_________________________

Top
#50733 - 07/14/04 12:49 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
Trixiem Offline
Post Master Sr


Registered: 03/10/03
Posts: 3031
Loc: Las Vegas, Nv
haha yea thanks chris, all credit goes to him for the nibbler idea

-kenny
Top
#50734 - 08/13/04 05:40 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
EngineNoO9 Offline
Post Master Supreme


Registered: 05/08/04
Posts: 20610
Loc: VA
two questions... how'd you connect wire to the sidemarker? you get a connector or something else?


*edit* got template to work now just curious bout wiring...

Edited by EngineNoO9 (08/13/04 05:47 PM)
Top
#50735 - 08/13/04 07:22 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
SiToeKnee Offline
Major Member


Registered: 11/13/03
Posts: 1447
Loc: Irvine, CA
Quote:

two questions... how'd you connect wire to the sidemarker? you get a connector or something else?


*edit* got template to work now just curious bout wiring...



We used crimp connectors that matched the size of the two connectors on the inside of the sidemarker light bulb socket. You can go to radio shack and find some. They look like this:



Just take the socket with you and ask someone to find a connector that will slide on to those two metal tabs inside the socket. Then you can use a wire crimper to attach the wire to run to the tap. Good luck.
_________________________
99 EBP Si I/H/E

Top
#50736 - 08/13/04 07:45 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
EngineNoO9 Offline
Post Master Supreme


Registered: 05/08/04
Posts: 20610
Loc: VA
ah ok yeah. i just thought of that as well honestly when i saw an extra one laying around here from installing something else.
Top
#50737 - 08/13/04 09:58 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
LilMrTinnie75040 Offline
Jr Poster


Registered: 08/12/04
Posts: 132
Loc: Garland, Texas
Very nice looking, good job. Does it work on a hatchback? ^.^
_________________________
"Turbo lag was invented for domestics to have a chance..." 97' Hatch trying to be transformed into a CTR.

Top
#50738 - 08/14/04 04:22 AM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
SiToeKnee Offline
Major Member


Registered: 11/13/03
Posts: 1447
Loc: Irvine, CA
Quote:

Very nice looking, good job. Does it work on a hatchback? ^.^



Of course.
_________________________
99 EBP Si I/H/E

Top
#50739 - 08/15/04 07:28 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
EngineNoO9 Offline
Post Master Supreme


Registered: 05/08/04
Posts: 20610
Loc: VA
just did it today on my hatch. looks nice
Top
#50740 - 08/16/04 03:20 AM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
SiToeKnee Offline
Major Member


Registered: 11/13/03
Posts: 1447
Loc: Irvine, CA
Quote:

just did it today on my hatch. looks nice



awesome!
_________________________
99 EBP Si I/H/E

Top
#50741 - 09/18/04 04:01 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
2000CheetahStud Offline
Post Master Supreme


Registered: 02/10/03
Posts: 49679
Loc: Cincinnati, OH
bump for people. Im trying it soon as well...Ill post pics when done!

matt
_________________________
2016 4Runner Trail Edition | 2000 Honda S2000

Top
#50742 - 09/19/04 01:07 AM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
SiToeKnee Offline
Major Member


Registered: 11/13/03
Posts: 1447
Loc: Irvine, CA
Quote:

bump for people. Im trying it soon as well...Ill post pics when done!

matt



good luck, hope everything works out for you.
_________________________
99 EBP Si I/H/E

Top
#50743 - 09/19/04 12:04 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
JDM_coupe Offline
Poster


Registered: 08/31/04
Posts: 265
Loc: Mississauga, Ontario, Canada
hey thx for the writeup cuz i did it on my ek and it looks GREAT!
_________________________

BaBy Nathan, daddy loves YOU


Top
#50744 - 09/19/04 06:22 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
2000CheetahStud Offline
Post Master Supreme


Registered: 02/10/03
Posts: 49679
Loc: Cincinnati, OH
Also, what should I use for connectors? Do I have to buy the honda ones? Or can I use radio shacks stuff? Andf how much for this? Thanks


matt
_________________________
2016 4Runner Trail Edition | 2000 Honda S2000

Top
#50745 - 09/19/04 09:55 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
SiToeKnee Offline
Major Member


Registered: 11/13/03
Posts: 1447
Loc: Irvine, CA
Quote:

Also, what should I use for connectors? Do I have to buy the honda ones? Or can I use radio shacks stuff? Andf how much for this? Thanks


matt



You can buy the Honda OEM plugs if you want, they are for the prelude i believe. I used radio shack spade connectors. I'm not sure what the price is off the top of my head, but you buy a package of like 10 for a few bucks. Sorry I can't be of more help. If you search for this same thread in the General Forum, you might find that some people used the Honda plugs and some used the spades.
_________________________
99 EBP Si I/H/E

Top
#50746 - 09/20/04 09:02 AM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
2000CheetahStud Offline
Post Master Supreme


Registered: 02/10/03
Posts: 49679
Loc: Cincinnati, OH
Could you show me the wiring diagram for NOT using the OEM harness please. I dont want pay the exra bucks. Haha. If you could, Id appreciate that. Woot!


matt
_________________________
2016 4Runner Trail Edition | 2000 Honda S2000

Top
#50747 - 09/20/04 11:25 AM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
SiToeKnee Offline
Major Member


Registered: 11/13/03
Posts: 1447
Loc: Irvine, CA
Quote:

Could you show me the wiring diagram for NOT using the OEM harness please. I dont want pay the exra bucks. Haha. If you could, Id appreciate that. Woot!


matt



it's actually pretty simple. it doesn't matter which plug taps what wire from the socket of the sidemarker. as long as one wire is tapped into the red wire and the other is tapped into the green. that's if you want them to stay on along with your parking lights. if you want them to only blink with your turn signals, then you will only tap one, i forgot which, i think i stated above which one, and the other wire to tap is the ground wire (black). hope that helps. not sure if that's what you were looking for. good luck.
_________________________
99 EBP Si I/H/E

Top
#50748 - 09/20/04 01:35 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
RyCeRoCkEtZ Offline
Post Master Sr


Registered: 10/26/03
Posts: 5553
Loc: NorCal, FrisCo, Bay Area!
Quote:

Good job guys. I'm impressed that you finally did it after all that talk. I told you it wasn't that difficult. The nibblers work pretty goo, huh?

Way to go on the write up. I never have the patiuence to document all my DIYs, so this should help everybody out.



Very very nice write up you guys and easy to understand, If i were to grade this as a college professor I'd give it a A++++!! . Hopefully I can get it started also.
_________________________
'00 EBP EM1 Si (K inspired) - Present, soon to be gone...
'05 TYB YZF R6 - sold 09-19-2007, you will be missed..
'08 TYB YZF R6 - 02-12-08
fAsT cAr aRe fOr dRaG rAcInG
fAsT dRiVeR aRe foR aUtOcRoSs

Top
#50749 - 09/20/04 07:53 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
Trixiem Offline
Post Master Sr


Registered: 03/10/03
Posts: 3031
Loc: Las Vegas, Nv
post them pictures

-kenny
Top
#50750 - 09/20/04 08:26 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
2000CheetahStud Offline
Post Master Supreme


Registered: 02/10/03
Posts: 49679
Loc: Cincinnati, OH
Havent done it yet. Markers are in the mail. Woot! Whats a shopping list I need for radio shack to finish this shizzit? Thanks guys


Cant wait!
Matt


Also, is the nibbler worth it if I have a dremel?
_________________________
2016 4Runner Trail Edition | 2000 Honda S2000

Top
#50751 - 09/20/04 11:10 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
IntenseCivic Offline
Post Master Jr


Registered: 10/31/02
Posts: 1821
Loc: Southern Cali (OC)
good write up tony and kenny.
_________________________
Now - '99 EBP Si
Past - R.I.P my '99 EBP Si 02/06/04
Click here for my FS & WTB post on 99-00 Si Parts!

Top
#50752 - 09/21/04 01:17 AM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
Trixiem Offline
Post Master Sr


Registered: 03/10/03
Posts: 3031
Loc: Las Vegas, Nv
hmm you need some wire T taps, 4 two on each side marker, and you need some wire, after that you need some spade connecters the ones that tony posted up you need about 4 of those too lol. The nibbler was honestly personal preference, if your good with a dremel you can use that, but we found it to be more accurate and you have more control over the cutting with the nibbler. It works like a holepuncher, but it punchs squares of metal out, so you put it where you wanna punch out and squeeze.

-kenny
Top
#50753 - 09/24/04 09:31 AM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
EngineNoO9 Offline
Post Master Supreme


Registered: 05/08/04
Posts: 20610
Loc: VA
Quote:

Quote:

Also, what should I use for connectors? Do I have to buy the honda ones? Or can I use radio shacks stuff? Andf how much for this? Thanks


matt



You can buy the Honda OEM plugs if you want, they are for the prelude i believe. I used radio shack spade connectors. I'm not sure what the price is off the top of my head, but you buy a package of like 10 for a few bucks. Sorry I can't be of more help. If you search for this same thread in the General Forum, you might find that some people used the Honda plugs and some used the spades.



i went to the honda dealer by me and the parts counter said he didn't think anything they had fit the connector. easier/cheaper to use the spade connectors and they fit snug too. i also sodered the wires off of the turn signals instead of cutting and splicing... haven't checked behind the markers since i did it but they're still working fine....
Top
#50754 - 09/25/04 08:01 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
2000CheetahStud Offline
Post Master Supreme


Registered: 02/10/03
Posts: 49679
Loc: Cincinnati, OH
Ok-

When I went to print out the template, it came out seeminly small. The mm measurements did not match up correctly. So what do I do? Thanks a lot fellas.

matt
_________________________
2016 4Runner Trail Edition | 2000 Honda S2000

Top
#50755 - 09/25/04 11:10 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
Noeladams Offline
Newbie


Registered: 09/25/04
Posts: 22
Loc: Greenville, SC
Quote:

Ok-

When I went to print out the template, it came out seeminly small. The mm measurements did not match up correctly. So what do I do? Thanks a lot fellas.

matt



I printed it out also and didnt come out to size I did take paint and enlarge it some but it was off then. Hmmmm any help guys?
_________________________
www.hondaasylum.com

Top
#50756 - 10/19/04 02:11 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
2000bluecivicsi Offline
Jr Member


Registered: 03/29/01
Posts: 438
I just got my sidemarkers and was wondering how these things stay in place?? is it just the clips on the sidemarker that holds them secure? so when i cut the hole and put the sidemarker in....will it just clip in and hold onto the fender? thanks guys.
_________________________
AIM: ebp2000si1

Top
#50757 - 10/19/04 06:34 PM Re: Trixiem & SiToeKnee's Sidemarker How-To *56k warning*
SiToeKnee Offline
Major Member


Registered: 11/13/03
Posts: 1447
Loc: Irvine, CA
Quote:

I just got my sidemarkers and was wondering how these things stay in place?? is it just the clips on the sidemarker that holds them secure? so when i cut the hole and put the sidemarker in....will it just clip in and hold onto the fender? thanks guys.



pretty much, that is why the hole you cut needs to be very exact so that the sidemarker holds to the fender securely.
_________________________
99 EBP Si I/H/E

Top
Page 1 of 3 123>


Moderator:  Dr. BrokenLimits, Professor Paki 
Hop to:
Shout Box

CSi Sponsors


ClubSi.com Shirts
ClubSi-Shirts
GameStop
Black-Friday Specials
Big Brake Kits
StopTech.Sale BBK Clearance
Brake Kits
Buy Brake Kits
EBC Brake Kits
EBC Brake Kits
BuyBrakes
Brake Kits-Pads & Rotors Sets
StopTech Brake Kits
StopTech
StopTech NZ
StopTech
StopTech Australia
StopTech
Hawk Brake Pads
Hawk Brake Pads
Samys Camera
GoPros, Cameras, Gear
Brake Specials Near Me
Brake Specials Near Me
Brake Pad Coupons
Coupon Code "hondafetish"
Porsche Brakes
Porsche Brake Upgrades
2-Piece Rotors-Civic Type-R
2-Piece Civic Rotors
Advertisement
My Cookies · Mark all read Powered by DallasColo (Dallas Colocation services) Contact Us · ClubSi · Top

| Brake Pads | | How To Change Brake Pads | | Drilled Slotted Brake Kits Cheap | EBC Brake Kits | Performance Brake Kits | Brake Specials Near Me | How To Replace Brake Pads