Type R bottom end into 99-00 si (old post)

You are not logged in. [Log In] ClubSi » Forums » Performance Tuning Zone » NA Tuning » Type R bottom end into 99-00 si (old post)

Page 2 of 2

Topic Options

#21959 - 10/11/02 02:46 PM Re: STICKY Type R bottom end into 99-00 si
Beave0101 Beave0101 servant of egosgame Registered: 02/13/02 Posts: 15941 Loc: San Diego	Well, since I"m comparing the price of having a b18c1 with type-r pistons, VS having a cooler engine name and getting the ITR block, if you could tell me what to look for or how much you paid for a ITR Block w/pistons......used...... -aaron
Top

Videos

#21960 - 10/11/02 02:50 PM Re: STICKY Type R bottom end into 99-00 si
blueSIguy blueSIguy Post Master Sr Registered: 06/12/00 Posts: 3950 Loc: NE	I'm no drag expert but damn, 185whp + 2600 car and 102 mph traps are impressive. _________________________ "Any society that would give up a little liberty to gain a little security will deserve neither and lose both"
Top

#21961 - 10/11/02 05:56 PM Re: STICKY Type R bottom end into 99-00 si
MacGyver MacGyver Post Master Registered: 04/25/00 Posts: 2321 Loc: The Deep South	the 185 whp was done on factory del Sol Si exhaust with a SOHC NON VTEC throttle body.. im projecting more like 190-195 with the exhaust and new throttle body Mac
Top

#21962 - 11/10/02 12:55 PM Re: STICKY Type R bottom end into 99-00 si
91civicSi 91civicSi Newbie Registered: 10/21/02 Posts: 22	wow that's good.. is b16head better than gsr if they both had the same internals? correct me if im wrong...
Top

#21963 - 11/10/02 09:36 PM Re: STICKY Type R bottom end into 99-00 si
MacGyver MacGyver Post Master Registered: 04/25/00 Posts: 2321 Loc: The Deep South	All things being equal as in cams and such. The GSR head with inherantly produce more hp due to a smaller combustion chamber. Thus this raises compression. Also the GSR head flows more CFM than an ITR head. But the GSR head induces turbulence in the air flow unlike the Type R head. Im not sure if the Type R head is better or not.. I personaly believe that the GSR head is better but i can not prove it.. Mac
Top

#21964 - 11/11/02 11:04 AM Re: STICKY Type R bottom end into 99-00 si
CivicSD CivicSD Post Master Jr Registered: 06/02/02 Posts: 1654 Loc: SAN DIEGO 858	Will my car pass smog with a ITR bottom end here in California? _________________________ "get your weight up, not your hate up"
Top

#21965 - 11/12/02 02:50 PM Re: STICKY Type R bottom end into 99-00 si
GuyWithSi GuyWithSi Jr Poster Registered: 06/01/01 Posts: 96 Loc: tx	so for 2200 or so the block comes with the piston and rod as well?
Top

#21966 - 11/14/02 03:22 PM Re: STICKY Type R bottom end into 99-00 si
00JunSi 00JunSi Jr Poster Registered: 08/11/02 Posts: 92	How do you figure the GSR head flows more CFM than an ITR head and produces more power? Do you have actual proof? I don't think Honda engineers would go with a poorer flowing head for an engine that requires more flow than a GSR.
Top

#21967 - 11/15/02 03:46 PM Re: STICKY Type R bottom end into 99-00 si
Beave0101 Beave0101 servant of egosgame Registered: 02/13/02 Posts: 15941 Loc: San Diego	In reply to: How do you figure the GSR head flows more CFM than an ITR head and produces more power? Do you have actual proof? I don't think Honda engineers would go with a poorer flowing head for an engine that requires more flow than a GSR.
Top

#21968 - 11/16/02 06:55 PM Re: STICKY Type R bottom end into 99-00 si
AzSi22 AzSi22 Major Member Registered: 10/31/99 Posts: 1386 Loc: Tucson, Arizona	This is Alaniz's comparison of a STOCK B16A head vs. a GSR head. If you look, the B16A head flows better for most of the midrange until about .450 lift. A ITR head is ported well with better valves and valvetrain, which do YOU think flows better???
Top

#21969 - 11/20/02 08:16 PM Re: STICKY Type R bottom end into 99-00 si
trans am killer trans am killer Post Master Sr Registered: 01/30/00 Posts: 5962 Loc: Rosemount, MN	im getting my C5 block and stuff ready and i was made aware that ITR pulleys (Power steering, alternator, and crank) would be a good idea. just to add something. may not be needed but may be a good idea, who knows... im just paying king motorsports to do it all for me so i dont have to worry about this shit. _________________________ AIM: LnDonSilver 1999 Impreza RS
Top

#21970 - 11/22/02 04:40 AM Re: STICKY Type R bottom end into 99-00 si
00JunSi 00JunSi Jr Poster Registered: 08/11/02 Posts: 92	So then explain to me why Honda would choose a poorer flowing head?
Top

#21971 - 12/08/02 03:15 AM Re: STICKY Type R bottom end into 99-00 si
trans am killer trans am killer Post Master Sr Registered: 01/30/00 Posts: 5962 Loc: Rosemount, MN	ok, we ran into a few problems with my setup, u CANNOT use b16 timing belt covers. u need ITR, all THREE of them. _________________________ AIM: LnDonSilver 1999 Impreza RS
Top

#21972 - 12/16/02 12:31 AM Re: STICKY Type R bottom end into 99-00 si
RyanSaysNo RyanSaysNo Post Master Jr Registered: 04/26/00 Posts: 1910 Loc: Rowland Heights, CA	wheres is the best place to purchase a shortblock because im lookin to get one soon. _________________________ SuKi 99 MR Si Aim: ryeislykebro
Top

#21973 - 07/18/03 12:15 PM 99 itr block with 2gen b16a head
jasma1 jasma1 Newbie Registered: 03/26/03 Posts: 48	i'm doing a 99 itr block with ctr pistons and b16a head with head work what ECU is good to use i have a second gen b16a ecu with pyr racing chip is that good to use pm me back thanks
Top

#21974 - 07/19/03 02:31 AM Re: STICKY Type R bottom end into 99-00 si
REDHCSI REDHCSI Poster Registered: 04/24/01 Posts: 310 Loc: Augusta, GA	Quote: just wanted to fill in about the header. from my very OWN personal experience a B16 header will not work with 1.8Liter motors. <br> <br>i recently switched from a 1st gen B16 header to a 94 GSR header on my LSvtec because the B16 header was giving me a bad exhaust leak between the exhaust manifold and downpipe.... because the damn downpipe was hitting the oil pan and thus it was not able to seal properly... <br> <br>so theres your .00001% [image]/images/icons/wink.gif[/image] <br> <br>(nice post btw Tom) with my ls/vtec setup i used my old dc sport b16 header <4-1> and it works just fine its a tight fit but it doesn't touch the oil pan
Top

#21975 - 08/01/03 06:22 PM Re: STICKY Type R bottom end into 99-00 si
TexasSI TexasSI Prenump? Post Master Sr Registered: 01/03/00 Posts: 9871	Fuck it i bought one too.. stock b18c5 Toda b16 head..ported by Portflow / retainers.Toda b cams .Toda valvetrain exedy clutch/toda flywheel. p28 kenji style, fields..Jdm 4-1 header jet hot coated, block is going in as we speak. _________________________ 💦
Top

#21976 - 09/23/03 12:18 AM Re: STICKY Type R bottom end into 99-00 si
SiRkid SiRkid Post Master Sr Registered: 12/06/00 Posts: 16338 Loc: On a boosted dog sled	ported well? better valvetrain? i guess... _________________________ http://www.digitallyimported.com "Horsepower is an patch for drivers who dont understand finesse."-exboyracer, some choada on spyderchat dot com
Top

#21977 - 09/23/03 02:23 PM Re: STICKY Type R bottom end into 99-00 si
Waffen Waffen Post Master Sr Registered: 09/10/02 Posts: 3490 Loc: San Gabriel Valley, Ca	Quote: Will my car pass smog with a ITR bottom end here in California? I doubt it only because it wouldn't pass visual, but maybe you could take it to a referee so they could recognize the new block code. _________________________ "The Edge... there is no honest way to explain it because the only people who really know where it is are the ones who have gone over. The others--the living--are those who pushed their control as far as they felt they could handle it, and then pulled back, or slowed down, or did whatever they had to when it came time to choose between Now and Later. But the edge is still Out there. Or maybe it's In." -HST
Top

Page 2 of 2

Previous Topic View All Topics

Index Next Topic

Moderator: Runnin@Redline Jr, Dr. BrokenLimits, The Mad Paki

Hop to:

Shout Box

CSi Sponsors

Civic Type-R 2-Piece Rotors — $814 Front Pair! Made in England!
View EBC Rotors

ClubSi.com Shirts

StopTech NZ
StopTech New Zealand

StopTech Australia
StopTech Australia

Brake Specials
Contact BuyBrakes

Brake Pad Coupon
Use Code: hondafetish